| 1 | Solid hardwood Oak, beech, or other hardwood boards | 25–40 mm (about 1–1.6 in) | Needs a sound sealed finish; standing water can mark the surface or affect joints. | Can be refinished, but may dent or scratch; use trivets for hot cookware. | Restaurants, pubs, cafés, and hospitality interiors where a natural wood appearance is desired. | Ask about wood species, moisture content, finish system, board-joint construction, and refinishing instructions. |
| 2 | Wood veneer on plywood Real-wood veneer bonded to a plywood core | 18–30 mm (about 0.7–1.2 in) | Surface protection depends on the finish; exposed edges and damaged finish can allow moisture ingress. | Veneer is thinner than solid wood and cannot be sanded repeatedly; protect from sharp impacts and hot items. | Dining areas and lounges seeking a wood look with a stable engineered panel. | Check veneer thickness, edge treatment, core grade, and whether the finish is suitable for frequent cleaning. |
| 3 | High-pressure laminate (HPL) on particleboard | 25–38 mm (about 1–1.5 in, including core) | HPL faces resist many everyday spills; unsealed seams and edges may be vulnerable to water. | Generally easy to clean and resistant to everyday wear; not immune to chips, deep scratches, or direct high heat. | High-turnover cafés, food-service spaces, and casual dining areas. | Confirm HPL grade, core material, edge profile, seam sealing, and cleaning-chemical compatibility. |
| 4 | HPL on plywood Decorative HPL bonded to a plywood core | 18–30 mm (about 0.7–1.2 in) | HPL provides a cleanable face; edges and joints still need suitable protection from moisture. | Face performance is similar to other HPL surfaces; the panel can chip or be damaged by concentrated impact. | Commercial dining where a durable decorative surface and a plywood panel are specified. | Request details on plywood grade, laminate bonding, edge banding, and intended indoor or outdoor use. |
| 5 | Compact laminate Solid-core high-pressure laminate panel | 10–13 mm (about 0.4–0.5 in) | Typically moisture resistant throughout the panel; confirm product suitability for the exposure and installation. | Durable for many commercial uses, but edges can be damaged by severe impact; use trivets for very hot items. | Busy cafés, bars, and settings where a slim, low-maintenance top is preferred. | Check panel thickness, support spacing, edge finish, fixing method, and manufacturer load guidance. |
| 6 | Solid surface Acrylic- or polyester-based mineral-filled surface, often supported by a substrate | Commonly about 12 mm surface sheet, with overall build-up varying by design | Nonporous surfaces are generally easy to clean; follow the supplier’s guidance for stains and disinfectants. | Can scratch and may be damaged by high heat; many surface scratches can be repaired, depending on the product. | Bars and hospitality interiors requiring a seamless-looking surface or integrated details. | Clarify surface composition, substrate, seams, repair method, and heat limitations. |
| 7 | Stainless-steel-clad top Stainless sheet over a rigid support core | Often 0.8–1.5 mm steel skin over a substrate; total top thickness varies | Stainless steel is corrosion resistant, but grade, finish, cleaning products, and exposure affect performance. | Can scratch and show fingerprints; hot items may transfer heat to the top and its support structure. | Bars, cafés, and service areas where a hygienic, wipe-clean metal surface is useful. | Specify stainless grade, sheet thickness, brushed or polished finish, core, edge detail, and cleaning instructions. |
| 8 | Porcelain or ceramic slab Large-format surface fixed to a structural support | Commonly 6–12 mm slab, usually installed with a supporting substrate | Many porcelain surfaces have low water absorption; joints and edges remain important to the complete assembly. | Surface is generally hard and scratch resistant, but edges can chip and concentrated impact can cause breakage. | Hospitality spaces seeking a stone-like appearance and a hard-wearing surface. | Check slab support, edge protection, joint design, impact guidance, and the supplier’s cleaning recommendations. |
| 9 | Tempered-glass top Glass panel mounted on a compatible frame or base | Commonly 8–12 mm, depending on panel size and support design | Nonporous and easy to wipe; fingerprints and smudges are readily visible. | Resists many surface scratches in normal use, but can break from impact or edge damage; use heat-resistant pads as advised. | Bars and lounges where a transparent or visually light tabletop is preferred. | Specify tempered safety glass, polished edges, support points, panel dimensions, and replacement procedure. |
| 10 | Powder-coated steel top Formed steel sheet with a protective coating | Often about 1–2 mm sheet, with stiffness depending on formed edges and support | Coating protects the steel when intact; chips or damaged areas may expose the metal to corrosion. | Coating can chip or scratch under hard impact; avoid abrasive cleaning that can damage the finish. | Industrial-style cafés, patios with suitably specified products, and casual dining areas. | Confirm steel thickness, coating specification, corrosion protection, drainage details, and indoor/outdoor rating. |